Borunte Robot Co., Ltd. is one of the most reliable manufacturers and suppliers of one axis ac servo injection manipulator arm in China, also supports customized service with low price. Please feel free to wholesale advanced one axis ac servo injection manipulator arm for sale here from our factory.
One axis servo manipulator BRTP07ISS1PC:
Short description: BRTP07ISS1PC series applies to all types of horizontal injection machines of 60T-200T for take-out products. The up and down arm is a single sectional type.
Main Specification:
Recommended I.M.M (ton): 60T-200T
Vertical Stroke (mm): 750
Traverse Stroke (mm): /
Max loading (KG): 2
Weight (KG): 50
One axis AC servo injection manipulator arm BRTP07ISS1PC
Product Introduction:
BRTP07ISS1PC series applies to all types of horizontal injection machines of 60T-200T for take-out products. The up and down arm is a single sectional type. The up and down action is driven by AC servo motor, with accurate positioning, fast speed, long service life, and low failure rate. The rest parts are driven by air pressure. It is economical and affordable. After installing this robot, productivity will be increased by 10-30%.
Basic Parameters:
|
Power Source (KVA) |
Recommended I.M.M (ton) |
Traverse Driven |
Model of EOAT |
|
|
1.27 |
60T-200T |
AC Servo motor,Cylinder drive |
zero suction zero fixture |
|
|
Traverse Stroke (mm) |
Crosswise Stroke (mm) |
Vertical Stroke (mm) |
Max.loading (kg) |
|
|
/ |
115 |
750 |
2 |
|
|
Dry Take Out Time (sec) |
Dry Cycle Time (sec) |
Swing Angle (degree) |
Air Consumption (NI/cycle) |
|
|
1.4 |
5 |
/ |
3 |
|
|
Weight(kg) |
||||
|
50 |
||||
Model representation: W: Telescopic type. D: Product arm +runner arm. S5: Five-axis driven by AC Servo Motor( Traverse-axis,Vertical-axis + Crosswise-axis).
The above-mentioned cycle time are the results of our company's internal test standard. In the actual application process of the machine, they will vary according to the actual operation.
Trajectory chart:
|
A |
B |
C |
D |
E |
F |
G |
H |
|
1577 |
/ |
523 |
500 |
1121 |
881 |
107 |
115 |
|
I |
J |
K |
|||||
|
224 |
30° |
90° |
|||||
No further notice if the specification and appearance are changed due to improvement and other reasons. Thank you for your understanding.
FUNCTION
5.1 General function
In the status of STOP and AUTO, Press "FUNC" key to enter Function page, Use up/down key to move to each function, you can press STOP key to leave Function page and return Stop page.
1,Language：Language Selection
2,EjectCtrl：
NotUse：Allow the thimble signal long-term output, Thimble action of injection does not be controled.
Use ：When the robot began to move, Disconnect thimble signal and start timing,. Allow to output thimble signal after thimble delay time.
3,ChkMainFixt：
PositPhase：Positive detected fixture switch. Fixture switch signal will be ON when Fetch success in AUTO mode.
ReverPhase：RP to detect fixture switch. Fixture switch signal will be OFF when Fetch success in AUTO mode.
NotUse：Not detect fixture switch. Not detect switch signal no matter what the Fetching action success or not.
4,ChkViceFixt：The same as Chk ChkMainFixt.
5,ChkVacuum：
Not Use：Not detect vacuum switch signal at Automatic run-time.
Use：Vacuum switch signal will be ON when Fetch success in AUTO mode.
Hot Tags: one axis ac servo injection manipulator arm, China one axis ac servo injection manipulator arm suppliers, manufacturers, factory, Five Axis Stamping Robot, Flexible Welding Robot, High speed 5 Axis Servo Robot, high speed robotic palletizer