BRTB08WDS1P0F0：
Short description: One axis plastic molding injection manipulator robot BRTB08WDS1P0/F0 is telescopic type, with a product arm and runner's arm, for two plate or three plate mold products take out. The traverse axis is driven by an AC servo motor.
Main Specification:
Recommended I.M.M (ton): 120T-250T
Vertical Stroke (mm): 800
Traverse Stroke (mm): 1250
Max loading (KG): 3
Weight (KG): 198
One axis plastic molding injection manipulator robot BRTB08WDS1P0F0
Product Introduction：
BRTB06WDS1P0/F0 traversing robot arm applies to all types of horizontal injection machine ranges of 120T-250T for take-out products and sprue. Single-axis drive control integrated control system: fewer signal lines, long-distance communication, good expansion performance, strong anti-interference ability, high accuracy of repeated positioning, can control multiple axes at the same time, simple equipment maintenance, and less failure rate.
Basic Parameters:
|
Power Source (KVA) |
Recommended I.M.M (ton) |
Traverse Driven |
Model of EOAT |
|
1.69 |
120T-250T |
AC Servo motor |
One suction one fixture |
|
Traverse Stroke (mm) |
Crosswise Stroke (mm) |
Vertical Stroke (mm) |
Max.loading (kg) |
|
1250 |
P:300-R:115 |
800 |
3 |
|
Dry Take Out Time (sec) |
Dry Cycle Time (sec) |
Air Consumption (NI/cycle) |
Weight (kg) |
|
1.7 |
6.49 |
3.5 |
198 |
Model representation: W: Telescopic type. D: Product arm +runner arm. S5: Five-axis driven by AC Servo Motor( Traverse-axis,Vertical-axis + Crosswise-axis).
The above-mentioned cycle time are the results of our company's internal test standard. In the actual application process of the machine, they will vary according to the actual operation.
Trajectory chart:
|
A |
B |
C |
D |
E |
F |
G |
H |
|
1340 |
2044 |
800 |
388 |
1250 |
354 |
165 |
210 |
|
I |
J |
K |
L |
M |
N |
O |
|
|
135 |
475 |
520 |
1190 |
225 |
520 |
1033 |
No further notice if the specification and appearance are changed due to improvement and other reasons. Thank you for your understanding.
One axis plastic molding injection manipulator robot System Installation:
1) A skilled electrician must complete all wiring work.
2) Turn off the power before beginning the process.
3) Only put it on flame-retardant materials like metal and keep it away from flammable things.
4) It must be safely grounded when in operation.
5) If the external power source malfunctions, the control system will fail. To ensure that the entire system operates safely, please configure the safety circuit outside of the control system. BORUNTE Injection Molding Control System, Multi-axis 269.
6) Prior to installation, wiring, operation, and maintenance, the operator must be conversant with the contents of this handbook. It is also required to have a thorough understanding of the appropriate mechanical and electronic expertise, as well as any applicable safety precautions.
7) The electrical control box used to install the controller should be adequately ventilated, oil-proof, and dust-proof. If the electric control box is airtight, the controller's temperature will likely be too high, affecting regular operation. Therefore, an exhaust fan must be fitted. The appropriate temperature in the electric control box is less than 50°C. Do not use it in areas where there is condensation or freezing.
8) To avoid unwanted surge interference, do not put the controller too close to the contactor, transformer, or other AC accessories. Caution: Improper handling may result in dangers such as personal harm or machine accidents.
Hot Tags: one axis plastic molding injection manipulator robot, China one axis plastic molding injection manipulator robot suppliers, manufacturers, factory, High Precision Three Axis AC Servo Industrial Robotic Arm, Four Axis Loading And Unloading Robot, Six axis Stamping Robot, 5 Axis Robot, , swing arm manipulator